UPenn Researchers Design Mylar-Based Insulation for Moon Bases

Researchers at the University of Pennsylvania designed a durable thermal insulation material using layered Mylar films to protect lunar bases from extreme temperatures.

Establishing a permanent human presence on the Moon requires shielding equipment and habitats from surface temperatures swinging from hundreds of degrees below zero to boiling heat. Traditional insulators like aerogels and multilayer insulation prevent heat transfer effectively, but their delicate internal structures easily suffer damage from handling, compression, and impacts.

University of Pennsylvania researchers built hybrid layered insulating film stacks, or HyLIFS, using hundreds of extremely thin Mylar sheets. The polymer, chemically known as biaxially oriented polyethylene terephthalate or BoPET, is commonly found in lightweight emergency blankets and food wrap.

“These stacks of Mylar can bend, withstand substantial compression and maintain their insulating performance, potentially allowing them to be packed, transported and survive rough treatment over many years of use,” said Igor Bargatin, Associate Professor in Mechanical Engineering and Applied Mechanics at the institution.

Balancing physical durability with thermal performance

The team coated select Mylar samples with extremely thin layers of aluminum oxide, also called alumina, to increase stiffness. Assembling the experimental stacks required painstaking manual work with tweezers and small weights.

“At the moment, the process is very time-consuming,” said Danielle R. Levin, a recent doctoral graduate in chemistry who also received a master’s degree in mechanical engineering and applied mechanics, in an interview with Science Daily. “We use two pairs of tweezers and small weights to handle and stack the delicate films. Even breathing near the stack can send the layers flying.”

Tests in a vacuum showed that the best stacks achieved thermal conductivity comparable to advanced vacuum insulation materials. The researchers subjected the material to compressive stress of approximately 20 megapascals, equivalent to 200 pounds of force on a fingertip area, repeating the test 10 times.

“We were concerned about the material failing under such high compressive stress,” Levin told Science Daily. “But the stacks didn’t survive just one high stress cycle — they survived 10 in a row.”

Alternative lunar construction approaches using simulated regolith

While the University of Pennsylvania team focused on flexible insulation, researchers at the University of Arkansas pursued rigid structural components. Scientists there demonstrated that simulated lunar dust can be 3D-printed into interlocking bricks without adding external binding agents, as SciTechDaily reported.

The Arkansas team used a laser powder bed fusion technique to sinter particles of lunar regolith together. This method avoids importing heavy binding materials from Earth, though the resulting blocks currently face strength limitations for active lunar construction.

Scaling up laboratory insulation for space missions

The experimental HyLIFS samples currently measure about one square centimeter, making continuous roll-to-roll manufacturing necessary before large sheets can cover a lunar habitat. Future testing must determine whether scaled-up versions retain their mechanical strength and thermal properties after repeated bending and scratching.

“The combination of thermal and mechanical robustness is critical for long-term use on the Moon,” Levin said. “This material could open a pathway to inexpensive, durable and reusable lunar insulation.”

The findings appeared in ACS Applied Materials & Interfaces under grant support from the National Science Foundation and the University of Pennsylvania School of Engineering and Applied Science.

Common questions about lunar base insulation

What makes traditional space insulation unsuitable for active Moon bases?

Aerogels and standard multilayer insulation are exceptionally lightweight and efficient at blocking heat, but their delicate structures tear easily under physical compression or accidental impacts from astronauts.

How does adding alumina affect Mylar film stacks?

Coating the thin polymer sheets with aluminum oxide increases their stiffness and durability under high compressive stress without sacrificing thermal performance.

What manufacturing hurdles remain for HyLIFS materials?

Laboratory samples measure only about one square centimeter and require manual stacking with tweezers, requiring engineers to develop continuous coating and assembly methods for large sheets.

Frequently asked questions on lunar construction

Can lunar dust be used directly for building structures?

Researchers at the University of Arkansas demonstrated that simulated lunar dust can be 3D-printed into interlocking blocks using laser powder bed fusion, though the material requires further strength improvements for large structures, SciTechDaily reported.

What pressure levels did the Mylar stacks survive in testing?

The film stacks tolerated compressive stresses of approximately 20 megapascals across 10 cycles while maintaining their insulating performance.

Who funded the University of Pennsylvania research project?

The study received funding from the National Science Foundation Division of Chemical, Bioengineering, Environmental and Transport Systems under grant number 1845933, alongside support from Penn Engineering.

The research was carried out at the University of Pennsylvania School of Engineering and Applied Science by co-authors Igor Bargatin, Danielle R. Levin, Matthew F. Campbell, Gulzhan Aldan, and Orevaoghene H. Omodior.